Nothing particularly amazing but a story nonetheless. Gather round everyone as I tell a tale how my unhealthy eating habits were both saved and squandered by riding my XR!
Last week I fancied some fast food. Lockdown in the UK started up again but for the first few days it seemed my local McDonalds was still letting you enter to grab your order and go. This is great because you're not allowed to go through the drive thru without a vehicle. I've not seen a solid reason for it that would usually restrict other modes of transport that they do allow however I see their point at least. So when I pulled up last week to see nobody inside the dining area to let me in I had 2 choices. Go home and make myself food that wasn't going to satisfy my desire for fries and a vanilla milkshake oooooooooor try my luck riding through the mostly empty drive thru.
Well you know where this is going, off I rode round and wiggled about on the sensor to make sure it knows I'm there since I can't see any camera's for them to see vehicles waiting. They take my order and I roll over to the payment window with cars behind and in front. The lady at the window was rightfully perplexed by me seemingly hovering over with my card ready and a smile tucked behind my mask. Payment goes through and off to the next window with another confused member of staff holding my food and drink. A brief exchange in niceties and off I went to get home before my well earned nummies got cold since it's below freezing now.
So where's the issue I alluded to earlier you may ask? Well about 2 hours ago I was hungry and figured I'd have my weekly allowance. Once again the dining area is closed off so I can't go in to takeaway. Off I roll and once again jiggle in place on the sensor, through goes my order and I float in place waiting. Spotting a camera I decide to wave to it, this may have been my undoing as when I got to the window they were ready and waiting to tell me they had to unfortunately cancel my order as they cannot serve me. Having kind of expected this from day one I let them know it was no problem and I'll make my way through the exit. I can't fault them for doing their job so off I went back home. Knee's weak, arms not heavy because I'm not carrying home any dinner.
On the flip side I passed by a local pizza place that was still letting you go in so floated on in, grabbed a nibble and went home with some foodies.
So there you have it, my tale of fast floaty food that's going to have me needing to do a few more reps lifting my board to wear off.
@HanahsDax said in Everest & Mariana Trench Badge - Got Them.... Send That Stoke Box:
An invigorating way to start the day, collected my first time based Gold badge this morning. It also coincides with my current V1 day streak.
Very Nice, on both... Keep it rolling -🍩-
@Lia thanks! Had a look at some of your videos too, great riding. With winter setting in and dry days being few and far between in the UK at the moment I’m very tempted to try the badger waterproofing mod you’ve done.
Forgot to update here. Made a post on reddit but for transparency purposes I'll update this post too :)
Have been riding more and more in the watery depths and it looks like I found my limit. At least for now.
Was out riding in my usual stream when I dove above the rails again. This time I kept it under and rode it through. It's a really weird feeling.
Didn't notice any issues on the ride home but I noticed when I turn her off she turned back on a few seconds later. After about 7 attempts I realised this was probably due to my earlier ride, water was inside and I needed to disconnect that battery ASAP.
BMS was dry and had no evidence of corrosion. It's covered in conformal coating so I'll expect corrosion near the connectors if any. Battery itself tested fine with each cell pair measuring within an acceptable tolerance of the others.
Controller side was another story. The controller was soaked, drops of water everywhere. This'll be what was triggering the board to turn back on. I know it doesn't take much, just touching the pins on the large battery connector is enough to trigger the BMS to turn on so the water was doing similar.
After removing the top plate I could see additional water on the reverse side of the PCB
In the bottom of the controller box were puddles, yeah I took it too far clearly. Not quite sure where it all came in mind you but I suspect it was around the threading on the power button and charge connector.
Battery box was mostly dry, there was some water in it still especially around the rear lights.
Condensation had formed on the rear lights, I did hear some hissing as I took the onewheel apart around the battery box so seeing this with 0 damage to the BMS has me suspect the rear light has been damaged.
Rear light connector has corrosion, some of the pins have gone blue.
Same can be said for the other side of the connector, this having a lot more corrosion on it. Need to scrape it all off and check connectivity
After cleaning it up I found one of the via's on the rear light PCB was dead so I bodge wired from the output of the connector round to the corresponding pin on the LED bank (was the red ones)
My board is plagued by broken solder joints. My front LEDs actually stopped working not because the cable broke but the connector had broke a pin loose. While testing the light states with the motor plugged in I noticed the lights flickered between states when turning the wheel. Seemed like one of the motor sensor connections were broke. Having already had to bodge wire the front left footpad sensor a few months back I decided to save myself from this again and just bodge wired every active pin on the motor sensor and footpad sensor connector.
After the wiring work I sealed up my controller and battery box ready to seal it up again with the last of my Badgerwheel kit.
Lots of silicone, who needs an internal gasket when you can just gunk the outside ;)
All re-assembled and everything works again. Bonus points for finally getting my front light back up and running after so many months of it being flickery.
I still believe the Badgerwheel kit is great, my last application was 7 months ago and I feel I didn't do the best of jobs applying it. Will be doing a proper seal job soon so I can continue pushing my luck.
Hope the small diagnostics and teardown is useful to anyone. It wasn't the most amazing of fixes since the board hadn't actually suffered any terminal issues.
I mean do whatever you want but this just seems dumb, especially on the Pint. I just broke my collarbone riding on the beach and I was only going 12mph AT MOST but probably more like 10. (I was in "Redwood" mode for the lower top speed). PS sorry about the imperial units, I am a dumb American.
Found my new favourite spot to ride, only possible when it’s as shallow as this.
Most of the vid is in water so viewing may be uncomfortable for some floaters, discretion is advised 😉
Looked like I was getting her deeper than what shows on the vid, guess I can attempt the middle next time where it gets a little deeper.