DIY "mobile supercharger"
@SkyPilot 2 and 3 need +
kbern last edited by
@SkyPilot @wr420 yup, pin 2 & 3 are both "+", per the instruction page (though that tidbit is easy to miss):
and I tested both + pins with a voltmeter to make sure they both had good connections.
Thanks for brainstorming. Let me know if you can think of any other potential issues.
cr4p last edited by
since the question with the pins is already answered I just like to add another thing:
if you guys are using the (very comfortable) MPT-7210A, I THINK that you it would be a good idea to use a battery pack/configuration with a higher voltage. altough the spec/user manual of the solar charger says it´s capable of 12 to 60V, it seems like on the lower voltage side it limits the current output which leads to longer charging times. so if this theory is correct, the more towards the 58.4V you go, the better (also the efficiency would improve I guess). As an alternative you might find a better step-up-converter which is really capable of delivering the required output current with 12V inputs.
as mentioned, that´s just a guess - has yet to be confirmed;-)
@kbern have you attempted to hook this up via power supply, and did you get the same results? If the power supply was faster, then it maybe related to the battery's discharge rate. The inverter combined with the output rate may be exceeding the max discharge rate of the battery.
I'm thinking the MPT-7210a may have more overhead than everyone thinks when up converting 12v to 58v. I suggest increasing the battery voltage to 24 or 48 volts and see if there's an improvement (adjustable voltage power supply is ideal for testing.)
As I type this I'm realizing the problem may be combined in both the loss in up converting and the max discharge of the battery.
Just some suggestions, getting late here please forgive my rambling.
silvs last edited by
This might work. ;)
I was going to buy that one; have you tried it... does it do the job ? :P
@silvs yes! And at $130,000 it's a steal. Adding the trailer hitch to the Onewheel was a bit tricky.
TJ04 last edited by TJ04
I've attached a few pictures below.
I've tried two methods:
12v/10Ah (120Wh) LifePo4 battery + 300Watt power inverter + Onewheel supercharger
Total Weight (including Onewheel charger): 5lbs, 8oz
Results: Charge Onewheel 65% in 30min
12v/10Ah (120Wh) LifePo4 battery + 58v up-converter
Total Weight (no Onewheel charger needed): 3lbs, 15oz
Results: Charge Onewheel 72% in 90min
Needless to say, I'm disappointed with my results using setup #2 (basically the setup described in this thread) both in terms of the minimal charge improvement over the 120v inverter method but also/mostly in terms of the 90min charge time.
The thing I don't understand (which is probably why the charge time was so long) is that I programmed the up-converter to deliver 58v and 3.5a but it only actually was delivering at 1.1a. Did I do something wrong? Do I need a different kind of battery? Any suggestions would be appreciated.
Might be the solar controller.
Anyone tried this method.. swapping out the capacitors to improve the performance:
Question: Connecting 16 of 3.6V batteries in series gets 57.6V. Is this a possible solution so you don't need a converter? I wonder how many amp hours would be sufficient for a charge.
Edit: by my calculations a 3000 mA battery would give 171 Wh so you could get a full charge with it. It would be more efficient because with the step up converter from 14V to 58V, you lose 10 to 15% or so efficiency with the heat lost in conversion and cooling fan. If you attach another 16 batteries in parallel that gives 341 Wh. That would give 2.5 charges in theory. Also since it is the same specs, you may (?) be able to use the Onewheel charger to also charge the spare battery pack. This way you are spending all of your money on batteries and not on a up converters or chargers.
The two questions I have is is a battery of that voltage dangerous and would the small voltage difference 57.6 v 58.4 I've been reading and the batteries are key. Alot of these are Chinese rip offs that overstate the mAh.
Initial test. Just used the Chafon dc out (without the AC adapter - hooked two of the DC outs in parallel to get the amperage up) with an upconverter to get to 58.4 volts, i.e., not using the AC charger. It worked. I charged from 67% to 80% in 11 minutes. Chafon still reads 100%.
Since this is one conversion rather than two, it should be more efficient.
Chafon with stock adapter: 12 DC > 110 AC > 58.4 DC (2 conversions)
Chafon with DC up converter = 12V DC > 58.4 DC (1 conversion)
I have pics of all of the above. Will post more after more tests, but this looks good. I really think making a battery with higher voltage and upconverting DC to DC will give the best range for the lowest weight.
Edit: I don't think the Chafon has enough Amperage for this and the parallel connection didn't take. I think I need a better battery.