Fender made with a more appropriate material



  • @sfctac
    Same here but lower miles... after the first couple weeks I didn't jump off or dump my board much. As fate would have it my @njcustom Rambo fender didn't show up week 3-4 and has only taken a couple spills... 1 to avoid a car that could figure out if they wanted to let me cross, 1 for a nose dive and a recent dump because my Marty McFly Nike Mag shoes...



  • @sfctac said in Fender made with a more appropriate material:

    While I too would like a fender to be sturdy and cheap, I can't help but wonder if you are a new rider. When I bought my OW a few months ago, I was told at the store to gain experience before installing the fender. I've done 150 miles so far and I think it will be another 150 before I attach it.

    Would be interesting to know experiences of more experienced riders with their fenders.

    Yes, I'm a new rider. I've had my board 3 weeks as of today and have logged 167 miles. I've only come off the board 3 times. Yesterday when I came off the board it was on wet grass in a park. The fender busted up when crashing on GRASS. (note: temp was 82 - plastic was not cold. Mileage at time of crash was 155. I may be new to OW but I've taken to it quick. Regardless of my experience level, the fender is made of the wrong type of plastic. The shape and look of the fender is great, it just needs to be made of plastic that can give a little.



  • As cool as they look, I’ve avoided carbon fiber fenders for this reason.



  • Surprisingly I was able to repair the POS, FM plastic fender over the weekend. All four corners have been fixed and reinforced with JB Weld. We'll see how long it lasts. In the meantime I have been gathering the supplies needed to build a new fender out of a thick, rubber mud flap I purchased on amazon.



  • @njacobs thats an awesome idea! when you finish this i really want to see it



  • @pat_hurley
    Hey, I completed my mud flap fender today; I think it turned out pretty good. I may take it off and trim it, right now it's the same width as the board, I think maybe I'll shape it more like FM's fender. 0_1510466306984_Fender Off OW.jpg 0_1510466751296_flap to bracket.jpg 0_1510466960365_Mounted bracket.jpg 0_1510466989156_Finished product.jpg
    0_1510467008364_Side view.jpg



  • Great job. That will never break on you. Just a comment but watch the sharp corners on the angle bracket. I know it is shielded by the rubber material but in case you flip/launch the board, you wouldn't want that corner to hit soft tissue.

    Other than that - nicely done.



  • @gadgetrider said in Fender made with a more appropriate material:

    Great job. That will never break on you. Just a comment but watch the sharp corners on the angle bracket. I know it is shielded by the rubber material but in case you flip/launch the board, you wouldn't want that corner to hit soft tissue.

    Other than that - nicely done.

    Thanks. Yeah, maybe I'll round off the corner a bit. - I'll take care of that the same time as when I trim it.



  • Njacobs

    How is the new style fender holding up? I made the same style as you with the aluminum bracket like you have. Works good until I crash the OW a few times, I found the aluminum would bend inwards towards the wheel, and start rubbing the tire itself. Thinking I may need to switch from Aluminum to Steel on my brackets. I think I may be kinda hard on my OW. Love the look of the OW fender, but the material certainly seems like the wrong choice.



  • @gibby My DYI mud-flap fender is working great, I haven't had any issues.



  • I still have my first OW fender one of the holes cracked and it has a partial crack in the middle, what I did was take gafting tape and covered the finder in that and haven't looked back since and it looks prime.



  • @tony420121 do you have any photos to post?



  • I would also like to see what you did to repair it Tony. Thanks



  • I rode it in to the office today Ill take a photo later and show the board and the type a tape I used.



  • This post is deleted!


  • I operate the sales floor at the oldest and most experienced eBike Store in Portland, Oregon. We sell Onewheel products there as well as premium electric bikes.

    Part of my enjoyment of the float that we all love is not having our parts breaking off the board. Particularly the fender. I have made a magnetic fender mount for the Future Motion fender that holds on as needed and will allow detachment when desirable. You roll the board and torque it in any direction and it comes off. Currently we are testing the working prototype now.

    It really looks promising. I developed this initially due to pine needles and leaves jamming between the wheel and the fender. I would need to remove the fender every ten minutes just to clear the jam. For more info: rcyders@yahoo.com



  • @magiccarpetrider
    That's really cool and considerate for your customers! I would still forward the complaint to FM, maybe as a dealer you will have a little more clout than your average customer.
    Even though the magnetic mount is a huge improvement, it's not exactly a complete solution. In a perfect world the fender would not come off except when you actually want it to, and it wouldn't be fragile in the event that the OW lands on it



  • Yes FM, please use different (better) plastic for the fenders. I assume you can even use the same mold. Dirt bike fender type of plastic would work great! While you're at it, how about color choices for the fender?



  • @njacobs

    Your wish has been granted! I decided to make some cheap fenders out of a proper material, so I melted down some dirtbike fenders and made these! (Just kidding, they are vac formed)

    Indestructible Fender



  • @makermarc That's what I'm talking about! Will you be selling these?