Dive Safe front wheels.
@eckit could you post a pic of your “hyucks”? Just curious how you mounted the casters and just how goofy they look.
@OneDan this is exactly what I was hoping to hear. I don’t hear many stories of people pushing through the pushback during tight turns. These along with float plates sound like a great combo for when I finally get a —O—
@tomfoolery sure thing! Will post a few shots from a few angles shortly. It’s funny that you called the “hyucks” I actually named my XR “A-Hyuck” before I even thought to install these because I ride goofy.
As for how I mounted them, it’s not the most secure. But it does what I need them to do. I cruise, I don’t do tricks so they don’t get knocked around all that much. I just put the original hex screw through one of the mounting holes on each caster.
But they could be mounted in a much more secure way using a piece of plastic or vinyl like the stuff the float pads are made of as a base that then gets mounted to the board:
Cut the plastic or vinyl to size
Pre-drill 2 holes for each caster
Mount the casters to the plastic or vinyl
Then pre-drill two holes that line up with the holes already on the underside of the board
Mount the whole setup to the underside of the board using slightly longer hex screws than the stock ones.
When you see the photos; the black electical tape serves no purpose but aesthetics. It helps the casters blend in with the black stock bumpers.
eckit last edited by eckit
This post is deleted!
eckit last edited by eckit
@eckit pretty rad idea you came up with there. That’s funny you named your board goofy because you’re goofy footed. I’m new to this forum as I’m super interested in getting a OW and just wanted to learn as much about them as I can. I actually remember reading another thread where you said you named your board “Goofy” and thought that was cool because I also ride goofy footed. Could you post a pic of those things making contact with the ground?
@tomfoolery sure thing. Here are a few photos.
@eckit that’s awesome man!!! I love how you showed that they even make contact while turning. Have they come in handy yet? I. Curious as to how much a weighted, speedy contact would effect the surface of the bearings and if that would eventually effect if they rolled in their cups sometime down the road.
@tomfoolery they caught me from a nosedive once. I accelerated too fast up my driveway. Would’ve totally bit it if they weren’t there. They made a nasty grinding noise (think rocks in a tumbler)—but they did the job.
I also would’ve caught a corner at low speed once while pushing my turn radius but the bearing caught me instead and I just bounced right back up.
The bearings should be solid chrome or solid stainless steel—so they shouldn’t deform too terribly. They may scuff and even gouge if you hit them hard enough on pavement, but they should never crush or dent. If anything were to deform under stress, it would be the housing.
That said, a set of six of these ran me something like $20. So if they ever get too banged up, I’ve got a few replacements on deck.
I don’t know how they will handle high speeds, especially on rougher surfaces. I’d wager not too well. But then again, I’m not entirely sure how fangs would handle similar conditions. Those small wheels can catch a crack or seam in the pavement, too.
I don’t think there will ever be a foolproof nosedive prevention for all circumstances. But these “a-hyucks” give me a little more peace of mind than riding with naked bumpers.
Hamasvjnga last edited by
@eckit Very cool!
Ryusui last edited by
@eckit I wanna call them "Hyuck Pucks". 😂
So, remember when I mentioned how the bearings wouldn’t deform, but the housing would? That happened to me today. From a standstill in NYC, I mounted the board and leaned forward to go. Not sure why, but the board never balanced out and I just teatered over to the nose. There was a lump in the asphalt as there often are in NYC and the housing hit the lump before the bearing hit the ground. This deformed the housing to the point that the bearing isn’t free-spinning.
I consider my first version of the “hyucks” a failure because of this same type of nose dive happened at speed, I would’ve been thrown.
But that just means I have to go back to the drawing board.
I’ll post when I come up with a fix.
@eckit what are the housings made of? Metal or some sort of polymer?
Glyph last edited by Glyph
@eckit - found a reddit post where a guy did something very similar to yours - he mounted to the outside, which doesn't block his lights. But his bearings look smaller too, so they might be even more susceptible to damage/deformation causing the bearing not to roll than yours are:
I have the Fangs - even though I haven't actually needed them yet, in my one bad nosedive (before Fangs existed) I believe they would have helped me either recover, or bought me precious fractions of a second to react and either run it out or tuck and roll, instead of slamming down to pavement on my shoulder and busting it.
Your idea, that the wheel should roll omnidirectionally, seems like a good one - if there was a way to incorporate it into a Fangs-like build (which are v. easy to install and fairly unobtrusive, aesthetically), that could be good.
@Glyph that is awesome!
I am currently thinking up a quick way to mount them.
Some other things that I am taking into consideration:
Position (out of the way of the lights)
Lowering the profile of the housing or changing the angle of the housing (so it doesn’t catch before the bearing does)
Glyph last edited by
@eckit - this appears to be the bearing he used - with the way he mounted them, the housing is mostly inside the OW bumper AND angled, so the housing getting hit looks fairly unlikely to me.
The two main questions are how easy would this install be for the average bear (I don't own a drill press), and will that tiny little bearing actually keep rolling, once it's gotten scuffed on concrete and gotten grit and gravel up inside the housing? We don't use these on tennis courts, we use them on streets and sidewalks and driveways, and those are rarely 100% smooth and clean.
@Glyph @eckit hey guys. I don’t think you’d need a drill press to drill the holes into the bumper but what about these bad boys.the “flying saucer” style roller bearing looks like its a lower profile so shouldn’t interfere with anything under the bumper.
@tomfoolery the bearings seem small and the housing is BIG. Also, I couldn’t find any info on the load rating. You need to make sure that the bearings and housing can take the load involved in an impact.
@eckit if you go to the link that @Glyph posted and scroll down to the section where “customers who viewed this item also viewed “ you’ll see a little box with the saucer style rollers where they do give specs. Or you can just click here
hilby last edited by
If you wheel on a perfectly smooth flat surface all the time, those little training wheels may save you....but you're doing it wrong.